As a painting contractor I find that most contractors charge between $20 an hour and $45 an hour plus paint and materials pending overhead here in Pennsylvania i figure $30 an hour is a safe bet. figure a good painter should be able to prep a 12 x 12 to a 12 x 15 room, caulk, apply 1 or 2 coats to the ceiling 2 coats on the walls and 1 coat on all baseboards, trim, doors and crown moulding in an 8 to 9 hour day. This is with minimal or minor spackling repairs like nail holes and nail pops, not cracks and peeling tape. Thats extra paint is usually  $30 to $70 a gallon pending quality. A room this size will need 1 gallon for the ceiling 2 for the walls and maybe 1 gallon for the trim, doors ext... the square foot price is $1.50 - $3.00 as far as asking for money up front I never ask. If the home owner buys the paint there is no need for money and if your buying the paint and your an established contractor you have an account with your supplier's.  any ways that's my input and guidelines 
Load flat or eggshell exterior paint color into paint sprayer. Depending on intensity of hue, apply one or two coats of flat or eggshell exterior paint to entire house. Be sure to work your way from top to bottom in a smooth, controlled manner, overlapping each stroke by 8 inches. TIP: When changing exterior color from light to dark or dark to light, start with a coat of primer to ensure proper coverage. Primer is not necessary when a fresh coat of existing color is being applied.
Climate is another factor to consider. Sunlight, wind, rain and salty weather can all wear out exterior paint. Oil-based paint is durable against wind, rain and temperature changes, but sunlight tends to degrade it. Alkyd paint chalks and sheds very thin layers when it begins to wear. Latex paint is the more durable option for very sun-drenched and relatively dry climate areas. Latex paint with high vinyl content should be avoided, however. Acrylic resin is by far the more durable binder for outdoor latex paint.
Wilson Hampton Painting Contractors is Southern California’s most trusted name in wood finishing. From fine furniture refinishing and restoration to custom case work and Specialty finishes, we pride ourselves in returning wood furnishings back to their natural beauty. We can also age the look or create an exotic look of distress, crackling or glazing. Learn more about Wilson & Hampton Painting Contractors.
Sand the trim with a fine-grit sanding sponge. Sponges get into crevices where sandpaper can’t go and let you apply even pressure. Then apply the first coat of paint, let it dry at least 24 hours, lightly sand it again for a completely smooth surface, and apply the second coat. After each sanding, vacuum the trim, then wipe it down with a tack cloth to remove the dust.
Back to the article. You can add water to all latex based paints / thinner to oil based paint. The tinting base has absolutely nothing to do with it. Say you are working outside and throughout the day you have to add a little water to keep the same consistency. If somebody really tried to add 20% to 50% water they no longer would be painting they'd be performing a whitewash or pickle finish.
The cost to paint an average size room (10X12) ranges from $380-$790, not including ceilings, trim or cost of the paint. DIY, this can cost between $200-$300. When estimating the cost, painters will start with how much paint will be required to complete the job. To know this, they first need to know the size of the area to be covered. The easiest way to calculate the size of the paintable area is to add together the length of the wall and multiply it by the width of the room from floor to ceiling. The resulting amount is the room's square footage. This total is a starting point, as it is not all paintable surface. The painters won't paint the windows and doors, for example, and they must account for ceiling trim and baseboards as well. The next step is to subtract the area of the doors and windows -- along with the square footage of the trim and baseboards -- to get an average. Then, use the same calculation (length x width) on the windows, doors, trim and baseboards, and subtract all of those numbers. The result of this equation is the square footage of the room's walls. This is your surface area number. (Painters will typically add a little square footage back in to this amount to account for extra paint, which may be required.)
Wilson & Hampton provides the premier system for coating metal surfaces. Electrostatic painting is an efficient process where you can upgrade and rejuvenate your entire office or factory area in your choice of finishes at a fraction of the re-placement cost. Cabinets, lockers, machinery, Bathroom Partitions and much more can be painted in-shop or on-site by drawing the paint directly to the metal surface to be painted and “wrapping” around it, leaving no drips, spatter, or over spray.
The Lead Renovation, Repair and Painting (RRP) Rule establishes requirements for firms and individuals performing renovations, and affects contractors, property managers, and others who disturb painted surfaces.  It applies to work in houses, apartments, and child-occupied facilities (such as schools and day-care centers) built before 1978.  It includes pre-renovation education requirements as well as training, firm certification, and work practice requirements. 
The Lead Renovation, Repair and Painting (RRP) Rule establishes requirements for firms and individuals performing renovations, and affects contractors, property managers, and others who disturb painted surfaces.  It applies to work in houses, apartments, and child-occupied facilities (such as schools and day-care centers) built before 1978.  It includes pre-renovation education requirements as well as training, firm certification, and work practice requirements. 

Painting Contractor

×