I agree with JHs. If there is no new color on it at all, just talk to the painter about it, if it was an honest mistake (which can happen very easily while painting) your painter should have no problem fixing it. However, in my years of experience, it is not unusual for 2 coats of door paint (good quality) not to cover very well at all. I once painted a red door 7 times, plus a tinted prime coat before I found the door to be a solid color.
Thorough preparation is essential to ensure a good finish. Contractors might have to fill cracks or holes and remove old paint if it is badly worn, peeling or flaking. They remove all paint and apply a suitable primer to the bare surface. If the existing paint is in reasonable condition, they clean it and rub it with abrasive material to provide a key for the new paint. On new surfaces, such as bare wood or fresh plaster, they apply a suitable seal, followed by a primer coat.
Repaint — exteriors especially — before visible signs of wear appear, Bancroft says. Don’t wait until you see peeling or flaking paint. “If I have to spend 40 hours preparing the surface before we can paint, that time is going to result in a lot of extra costs. But if I can spend 10 hours preparing the surfaces to be painted, you’re going to save money,” Freeman says.
When requested by the party contracting for renovation services, must use an EPA-recognized test kit or must collect paint chip samples, submit them to an EPA-recognized laboratory, and obtain test results from the laboratory to determine whether components affected by the renovation contain lead-based paint.  Note: you must assume lead-based paint is present for housing and buildings covered by this rule, unless testing is done that determines the components affected are lead-free.
With that said, here's the reality of that particular scenario. Painters do put water in the paint, but not for reasons you would think. Some materials need to have their viscosity manipulated in order to slow drying time, allowing gravity to 'smooth' out the product for a better finish. It also prevents 'drags' and 'sausages'. I personally try not to do it too often, but from time to time I have to. I want my client to have a proper finish.
Brighten up your home. From DIY lighting that adds both value and light to your house, to unique painting ideas that go beyond picking out paint swatches, our real-life homeowner stories and expert advice can illuminate every room. What house painting tips can make the job go quicker with fewer mistakes? Which lighting ideas can create just the right ambiance?
The other difficult part is getting a painting contractor to show up. While this generalization does not apply to every painter, personally I am extremely grateful if I can get a paint contractor to show up to look at the house and to later produce a written estimate. I hardly fault the painting contractors, because I think it is a combination of the contractors being smaller operations along with a high demand for their work.
A textured wall will need more paint than a smooth wall. The texture adds more surface area, even though it doesn't increase square footage. Determining the additional surface area depends on how much texture there is. Painters will probably estimate about 300 to 350 additional square feet of paint to account for texture. Factor additional surface area into your square footage calculations when seeking professional estimates.

to be the devils advocate i have been a building contractor 20 of the last 30 yrs. i do know that if you go to a higher sheen of paint and or darker colors then any imperfections in the walls will show up much more dramatically…therefore the painter or a good drywall finisher is needed to prepare the walls extensively. this could cause more expenses…for it takes a lot of time to prep walls (smooth walls..not textured walls) and this cost has to be absorbed.


Another good rule of thumb is to test out colors on your home before you start. Once you’ve noted what others have done, and have visited a paint supply retailer to get some more ideas, test out a few potential colors on a nondescript part of your home just to make sure it’s what you expect. Colors that look fantastic on a tiny brochure can strike you a lot differently when they’re covering an area of a couple square feet. Try out a few options so you can compare them, and give yourself a few days to mull over your impressions. Taking this advice can save you the dilemma of what to do those 20 gallon buckets of “Green Myth” that you quickly realized looked more like split pea soup once you started slopping it on.
Good contracts include descriptions of prep work and repairs; paint specs by brand name, type, color and product number; the number of coats; and a full description of the work, including frequently omitted items such as cabinet interiors and shutters. Minimize delays by specifying that, weather permitting, work will be continuous. Get a payment schedule that minimizes the down payment — the more payment you can withhold until the end, the more leverage you'll have to get the job done well and per your specifications. Insist that contractors provide proof that they carry both general liability and workers' compensation coverage.
We used FHP to paint the interior of our home and  were very satisfied with their work. Joe, the owner, was always available to answer any questions I had. He put up samples for us in each room so we could choose the best color. They prepped the house well and the end product was more than expected! His price was fair compared to competitors. FHP finished the project in a timely manner . He even offered to come back and touch up the paint after we have moved in ! I would recommend FHP for any job!

When you’re ready to tackle your next paint project, we offer an amazing choice of colors from top paint brands, at the best price, and expert know-how to help you do the job right. Start outside by taking an inventory of your siding and trim. If your paint is fading or peeling off your siding, start the prep work by repairing the siding and trim with some waterproof patching compound. Once dry, sand and apply primer. Then, repaint those areas until your exterior looks fresh and clean.
basic formula? single color exterior labor only ranges from $0.85 to $0.95 per sq foot as a BASE starting point. Prices go up depending on multiple colors, slope of surrounding areas, multiple stories..etc.Some painters charge per window to mask off. Ive seen $25 a window to $50.  Interiors without flooring can be factored the same way. When you start having to do multiple colors, cut ins, masking, room isolation...etc. the price jumps considerably. I always start with a base of $0.85 a sq foot and figure it out from there. the season plays a major role too. paint and materials are charged separatly and are typically marked up at a minimum of 15%. I always tell clients this. that way they pick the paint out they want and what quality they want as well. Anyways...thats your base. 1250 sq foot home @ .0.95 a ft = $1,187.50 (one color). Pressure washing, Add another $45-$55 per hour. a 1250 sq ft home is not going to take longer than 2-3 hours if its a single story. 
The cost to paint an average size room (10X12) ranges from $380-$790, not including ceilings, trim or cost of the paint. DIY, this can cost between $200-$300. When estimating the cost, painters will start with how much paint will be required to complete the job. To know this, they first need to know the size of the area to be covered. The easiest way to calculate the size of the paintable area is to add together the length of the wall and multiply it by the width of the room from floor to ceiling. The resulting amount is the room's square footage. This total is a starting point, as it is not all paintable surface. The painters won't paint the windows and doors, for example, and they must account for ceiling trim and baseboards as well. The next step is to subtract the area of the doors and windows -- along with the square footage of the trim and baseboards -- to get an average. Then, use the same calculation (length x width) on the windows, doors, trim and baseboards, and subtract all of those numbers. The result of this equation is the square footage of the room's walls. This is your surface area number. (Painters will typically add a little square footage back in to this amount to account for extra paint, which may be required.)
When calculating total cost of your project, one of the most important factors to consider is the paint itself. Paint costs will be determined by the quantity of paint and primer required to complete your project, as well as the quality of the paint you choose. You can use this paint calculator to estimate how much paint you will need.. Once you have an idea what you're working with, go to your local home improvement store and compare the costs of a gallon in person. Painting professionals can also quote average prices from their years of experience working with different paint qualities.
Picking exterior house paint colors is a lot different than picking a color for a shirt or a car.  It may help to drive around to observe colors that other homeowners have combined on homes that are of similar size and design as yours.  There are also online resources that provide homeowners with the ability to create virtual makeovers of their home by combining colors together through their software programs as well.

When you choose Five Star Painting residential house painting contractors, you can feel confident that you are hiring the best in the business. Local Five Star painters have been serving clients throughout the United States and Canada since 2004. From taking time to prepare the area to using exactly the right equipment for each job, we make sure the project is done correctly. Our experience shows: We’re good at what we do, and our clients are always happy with the work we leave behind!


As you walk through your lighted rooms (preferably day light) see if the new coat has light spots showing the precious paint. This is call "bleeding through". This means that there's only one coat of paint or the paint was diluted or the trasition of colors were from light to dark (or the other way around) and primer was not use or the painter is inexperienced.
Inspect the surface area for holes, cracks or other problems and apply acrylic caulk to fill them in. Use a putty knife to smooth out the caulk and remove any excess to prevent bumps. For particularly thin or narrow crevices, you may have to use your finger to smooth out the caulk. Caulk contracts and shrinks, so apply a second layer once it's dried.
This was very helpful. I wonder if i would really follow through and check to see if my painter was cheating me. I used a painter I found on Angie's List. This was 5 years ago. He did a great job. I know he did patching only for about a day and a half. We decided on the kind of paint before he started. that is what he used. I don't know if I could stay on top of him and watch him open every can of paint.

This was very helpful. I wonder if i would really follow through and check to see if my painter was cheating me. I used a painter I found on Angie's List. This was 5 years ago. He did a great job. I know he did patching only for about a day and a half. We decided on the kind of paint before he started. that is what he used. I don't know if I could stay on top of him and watch him open every can of paint.

Painting Contractor Co

×